Configuring Cluster Servers

In this guide, we will assume that the following servers are being installed for the cluster:

  • Main Server: Install the PBX with an IP address of 192.168.1.20.

  • Server 1: Install a media server with a private IP address of 192.168.1.21 and a static public IP of 104.101.137.60.

  • Server 2: Install a queue server with an IP address of 192.168.1.22.

  • Server 3: Install a meeting server with an IP address of 192.168.1.23.

  • Server 4: Install an IVR server with an IP address of 192.168.1.24.

  • Server 5: Install an IM server with an IP address of 192.168.1.25.

A server can only deploy one type of PortSIP server at a time. For instance, it's not allowed to deploy both the media server and queue server simultaneously on Server 1.

Setup the PortSIP PBX

Before configuring the cluster servers, please ensure that you have completed the PBX installation and configuration on the Main Server by following the guide for Installation of the PortSIP PBX to install it.

Note: In this step, just need to install the PBX only, is no need to install the IM server at this stage, as it will be installed later in this guide.

All commands must be executed in the /opt/portsip directory.

Configure the Firewall

It is necessary to create firewall rules on the Main Server that allow the cluster servers to access the PBX server (Main Server).

To configure these firewall rules, please perform the following commands on the PBX server (Main Server).

sudo firewall-cmd --permanent --zone=trusted --add-source=192.168.1.21
sudo firewall-cmd --permanent --zone=trusted --add-source=192.168.1.22
sudo firewall-cmd --permanent --zone=trusted --add-source=192.168.1.23
sudo firewall-cmd --permanent --zone=trusted --add-source=192.168.1.24
sudo firewall-cmd --permanent --zone=trusted --add-source=192.168.1.25
sudo firewall-cmd --reload

To verify that the rule has been created correctly, you can use the following command:

sudo firewall-cmd --zone=trusted --list-all

The correct output should be like below:

[ubuntu@localhost ~]$ sudo firewall-cmd --zone=trusted --list-all
trusted (active)
  target: ACCEPT
  icmp-block-inversion: no
  interfaces: 
  sources: 192.168.1.21 192.168.1.22 192.168.1.23 192.168.1.24 192.168.1.25
  services: 
  ports: 
  protocols: 
  forward: yes
  masquerade: no
  forward-ports: 
  source-ports: 
  icmp-blocks: 
  rich rules:

To allow the entire C class address to access the PBX server (Main Server), you can use the following commands:

sudo firewall-cmd --permanent --zone=trusted --add-source=192.168.1.0/24  
sudo firewall-cmd --reload

In the future, if you add more servers to the existing cluster, you will need to create firewall rules to allow those servers’ IP addresses to access the PBX server (Main Server), just like the rules mentioned above.

Configuring the IP Address Whitelist

This step is mandatory; without it, the service will not work.

To prevent the PBX from limiting the cluster servers' request rate, we need to add the cluster servers' IPs to the whitelist in the PBX.

To do this, please follow the below steps:

  1. Sign in to the PBX web portal as the System Administrator

  2. Select the menu IP Blacklist > Add.

  3. Enter the cluster server IP as shown in the screenshot below and choose a long expiration date.

  4. Repeat the above steps for each cluster server.

Add the Cluster Servers

To add the cluster servers in the web portal, sign in to the PBX Web portal as the system administrator.

Disable Default Servers

The PortSIP PBX installation comes with default media, queue, meeting, and IVR servers. We recommend disabling these default servers so that the Main Server only handles SIP signaling, allowing it to support more users and calls.

To do this, please select the Servers menu, expand each server type(media servers, queue servers, meeting servers, IVR servers), and turn off the default server as the below screenshot shows up.

Note: The IM Server is no need to disabled.

Add Media Server

To add a new media server, select the Servers > Media Servers menu, click the Add button, enter the server information as shown in the screenshot then click the OK button to save it. Please remember the server name "media-server-1", we will use it in a later step.

Suggest don't set the Maximum of call sessions to more than 5,000.

Install Media Server

Please go to Server 1 (whose IP address is 192.168.1.21) to install the media server.

Make sure you have followed the guide for Preparing Cluster Servers on Server 1.

To install the media server, execute the following commands and pay close attention to the parameters:

  • -a 192.168.1.21: This specifies the private IP of Server 1.

  • -x 192.168.1.20: This specifies the private IP of the PBX Server (Main Server).

  • -s media-server-only: This indicates that only the media server should be installed.

  • -n media-server-1: This specifies the name of the media server, which must be the same as the name entered on the PBX Web portal in the previous step.

cd /opt/portsip
sudo /bin/sh cluster_ctl.sh \
run -p /var/lib/portsip \
-a 192.168.1.21 \
-x 192.168.1.20 \
-i portsip/pbx:22.0.33.1354-beta \
-s media-server-only \
-n media-server-1

If your media server is hosted on a cloud platform such as AWS or Azure, you will need to create a network rule in the cloud platform to allow the following ports:

  • 35000 - 65000: UDP

You can repeat the above steps to set up more media servers. Just make sure to use a different IP address and server name for each one.

If you set up multiple media servers, they must not use the same server name or IP address. Especially, you must ensure that the server name specified in the commands matches the one entered on the web portal.

Add Queue Server

To add a new queue server, select the Servers > Queue Servers menu, click the Add button, enter the server information as shown in the screenshot then click the OK button to save it. Please remember the server name "queue-server-1", we will use it in a later step.

Install Queue Server

Please go to Server 2 (whose IP address is 192.168.1.22) to install the queue server.

Make sure you have followed the guide for Preparing Cluster Servers for Server 2.

To install the queue server, execute the following commands and pay close attention to the parameters:

  • -a 192.168.1.22: This specifies the private IP on Server 2.

  • -x 192.168.1.20: This specifies the private IP of the PBX Server (Main Server).

  • -s queue-server-only: This indicates that only the queue server should be installed.

  • -n queue-server-1: This specifies the name of the queue server, which must be the same as the name entered on the PBX Web portal in the previous step.

cd /opt/portsip
sudo /bin/sh cluster_ctl.sh \
run -p /var/lib/portsip \
-a 192.168.1.22 \
-x 192.168.1.20 \
-i portsip/pbx:22.0.33.1354-beta \
-s queue-server-only \
-n queue-server-1

You can repeat the above steps to set up more queue servers. Just make sure to use a different IP address and server name for each one.

If you set up multiple queue servers, they must not use the same server name or IP address. Especially, you must ensure that the server name specified in the commands matches the one entered on the web portal.

Add Meeting Server

To add a new meeting server, select the Servers > Meeting Servers menu, click the Add button, enter the server information as shown in the screenshot then click the OK button to save it. Please remember the server name "meeting-server-1", we will use it in a later step.

Install Meeting Server

Please go to Server 3 (whose IP address is 192.168.1.23) to install the meeting server.

Make sure you have followed the guide for Preparing Cluster Servers on Server 3.

To install the meeting server, execute the following commands and pay close attention to the parameters:

  • -a 192.168.1.23: This specifies the private IP of Server 3.

  • -x 192.168.1.20: This specifies the private IP of the PBX Server (Main Server).

  • -s meeting-server-only: This indicates that only the meeting server should be installed.

  • -n meeting-server-1: This specifies the name of the meeting server, which must be the same as the name entered on the PBX Web portal in the previous step.

cd /opt/portsip
sudo /bin/sh cluster_ctl.sh \
run -p /var/lib/portsip \
-a 192.168.1.23 \
-x 192.168.1.20 \
-i portsip/pbx:22.0.33.1354-beta \
-s meeting-server-only \
-n meeting-server-1

You can repeat the above steps to set up more meeting servers. Just make sure to use a different IP address and server name for each one.

If you set up multiple meeting servers, they must not use the same server name or IP address. Especially, you must ensure that the server name specified in the commands matches the one entered on the web portal.

Add IVR Server

To add a new IVR server, select the Servers > IVR Servers menu, click the Add button, enter the server information as shown in the screenshot then click the OK button to save it. Please remember the server name "vr-server-1", we will use it in a later step.

Install IVR Server

Please go to Server 4 (whose IP address is 192.168.1.24) to install the IVR server.

Make sure you have followed the guide for Preparing Cluster Servers on Server 4.

To install the IVR server, execute the following commands and pay close attention to the parameters:

  • -a 192.168.1.24: This specifies the private IP of Server 4.

  • -x 192.168.1.20: This specifies the private IP of the PBX Server (Main Server).

  • -s vr-server-only: This indicates that only the meeting server should be installed.

  • -n vr-server-1: This specifies the name of the IVR server, which must be the same as the name entered on the PBX Web portal in the previous step.

cd /opt/portsip
sudo /bin/sh cluster_ctl.sh \
run -p /var/lib/portsip \
-a 192.168.1.24 \
-x 192.168.1.20 \
-i portsip/pbx:22.0.33.1354-beta \
-s vr-server-only \
-n vr-server-1

You can repeat the above steps to set up more IVR servers. Just make sure to use a different IP address and server name for each one.

If you set up multiple IVR servers, they must not use the same server name or IP address. Especially, you must ensure that the server name specified in the commands matches the one entered on the web portal.

Installing the IM Server

Currently, the IM server does not support cluster installations; it can be deployed as a standalone server. It can support up to 50,000 online users with a powerful CPU and memory(16 cores, 16GB).

To install the IM server on a server with the IP address 192.168.1.25, please follow these steps:

Generate a Token for the IM Server

  • Log in to the PortSIP PBX Web portal as the System Administrator.

  • Go to Servers > IM Servers.

  • Select the default server and click Generate Token.

  • Copy the generated token for later use.

Create and Run Instant Messaging Docker Instance

Use the following command to create the Instant Messaging (IM) service Docker instance in the server which has the IP 192.168.1.25. Replace each parameter with your actual values:

  • -E: Specifies that the IM server is installed in extended mode (required).

  • -p: Specifies the path for storing IM service data (required).

  • -a: Specifies the private IP address of this IM server. If this parameter is omitted, the -A parameter must be specified.

  • -A: Specifies the public IP address of this IM server. If this parameter is omitted, the -a parameter must be specified.

  • -i: Specifies the PBX Docker image version (required).

  • -x: Indicates the main PBX server's IP address (typically the private IP of the main PBX server) (required).

  • -t: Provides the token generated and copied in the previous step (required).

  • -f: Specifies the path for storing files sent in chats. This path must differ from the one specified with -p. If omitted, chat files will be stored in the path specified by -p.

sudo /bin/sh im_ctl.sh run -E \
-p /var/lib/portsip/ \
-a 192.168.1.25 \
-i portsip/pbx:22.0.33.1354-beta \
-x 192.168.1.20 \
-t MJC4NZBLYTGTZTJJNS0ZMWZHLWIXZDCTZJLLMDEWZJHKZTAY

Restarting Servers

After completing adding the cluster servers, now go to restart the servers to make them up.

Restart the Main PBX server

Perform the following command on the PBX Server (Main Server) to restart the service.

cd /opt/portsip
sudo /bin/sh pbx_ctl.sh restart

Restart the Resource Load Balancer

Perform the following command on the PBX Server (Main Server) to restart the resource load balancer.

cd /opt/portsip
sudo /bin/sh pbx_ctl.sh restart -s loadbalancer

Restart Media Servers

Go to each media server, and perform the below commands to restart the service.

cd /opt/portsip
sudo /bin/sh cluster_ctl.sh restart -s media-server-only

Restart Queue Servers

Go to each queue server, and perform the below commands to restart the service.

cd /opt/portsip
sudo /bin/sh cluster_ctl.sh restart -s queue-server-only

Restart Meeting Servers

Go to each meeting server, and perform the below commands to restart the service.

cd /opt/portsip
sudo /bin/sh cluster_ctl.sh restart -s meeting-server-only

Restart IVR Servers

Go to each IVR server, and perform the below commands to restart the service.

cd /opt/portsip
sudo /bin/sh cluster_ctl.sh restart -s vr-server-only

Now all cluster servers have been successfully up, you can check their status on the PBX Web Portal by going to the Servers menu, if everything has been set up correctly, the server status will be displayed as "Online".

Restart the IM Server

Go to the IM server, and perform the below commands to restart the service (please ensure the Main PBX service is started).

cd /opt/portsip
sudo /bin/sh im_ctl.sh restart

Upgrading Servers

It’s crucial to keep your cluster servers updated in line with the latest PortSIP PBX releases. This ensures that all features function as expected and that your system maintains optimal performance and security.

Whenever a new version of PortSIP PBX is released, it’s essential to upgrade your installed cluster servers as well. Follow the steps below to ensure a successful upgrade.

We use the media server as an example, you will need to replace the media server with other servers as your actual environment.

Upgrade the Main PBX Server

Upgrade the IM Server

Upgrade Other Servers

  1. Remove the current running server by the commands:

cd /opt/portsip
sudo /bin/sh cluster_ctl.sh stop -s media-server-only
sudo /bin/sh cluster_ctl.sh rm -s media-server-only

  1. Install the latest version of the server. Follow the instructions provided in the Add Cluster Servers guide to complete this step.

SBC Cluster

To deploy the SBC cluster, please follow this topic Deploy the SBC Cluster.

PreviousPreparing Cluster ServersNextManaging Cluster

Last updated